Newest
information
Product
information
Company
information
Inquiry Catalogue
request

  

  [ Headquarters sales division and Tokyo branch have been moved ]
Dear sirs,
Thank you for your continuous patronage and support extended to us.
We are pleased to notify you that with the aim of further expanding our business fields and enhancing the convenience the office of our Tokyo branch and the office of headquarters sales division have been moved to the following address as of 9th May,2016:

Tokyo branch
Shin Yaesu Bldg. 3F, 2-10-10 Yaesu, Chuo-ku, Tokyo 104-0028, Japan
Phone:+81-(0)3-3548-8100     Fax:+81-(0)3-3548-8101



Please be informed that the new office is in the vicinity of Tokyo Railway station within walking distance and so convenient that you may easily drop in when nearby.
Taking this opportunity we all would like to newly assure you of our continuous effort to meet your expectations.
Best regards,

-------------------------------------------------------------------------------------------
  [ Vertical Type Vacuum Injection Molding Machine for Rubber ]
Launched New Vertical Type Vacuum Injection Molding Machine for Rubber VS3 Series


VI-200V(S3)-40/70SPR2
Clamping Force KN (Ton) 1960 (200)
Injection volume cm3 1500
Total Height mm 4217
Total Width mm 1811
Total Depth mm 3247
Daylight mm 600
Stroke mm 400
Heating Platen Diameter mm 650 x 650
Work Height mm 897
Feature 1 Reduction of fraction defective
Vacuuming the area around the mold significantly reduces molding defects caused by air.
* Allows vacuum molding with molds not specifically engineered for vacuum molding.

Feature 2 Low workbench height
The workbench height is 101 mm lower than with our previous model, eliminating the need to set up another workbench and thereby improving work safety.

Feature 3 Saves space
The reduced dimensions maximize productivity from limited factory floorspace.

Feature 4 Energy efficient
The rotation control pump featuring an IPM motor and the high effectiveness insulation plate significantly reduce power consumption. While actual power savings will vary with molding conditions, power consumption is typically 30% lower than with our previous V(S2) model.

Feature 5 Reduced molding cycle times
The reduced space inside the vacuum frame decreases the time required to achieve a vacuum, thereby shortening molding cycle times.

Feature 6 Improved maintenance efficiency
Raising the vacuum frame opens up the machine, just like a vertical type injection molding machine, dramatically improving maintenance efficiency for wiring/piping work around the mold.
The design also minimizes accumulations of rubber burrs that can cause machine problems and makes the machine easy to clean.

-------------------------------------------------------------------------------------------
  [ Vibration endurance testing machine ]
Launched New Vibration endurance testing machine MVE-10K


A great aid for product developers!
Applies vibrations to sample products under set temperature conditions for durability testing.
Matsuda Seisakusho suggests the optimal testing machine for each customerfs specific needs.

 
MVE-10K
Maximum vibrational exciting force }10 KN
Maximum amplitude }50 mm
Maximum frequency 40 Hz
Maximum speed }1 m/s
Maximum acceleration }100 m/s2
Temperature range -40C
+230C
Test chamber inner dimensions Width: 1,200 mm
Depth: 1,200 mm
Height: 700 mm

This testing machine applies vibrations to sample products under set temperature conditions for durability testing.
Features
@ Allows user selection of vibration frequency and amplitude.
A Allows user selection of temperature settings.

-------------------------------------------------------------------------------------------
  [ Injection Molding Machine for Rubber ]
Launched New Vertical Type Injection Molding Machine for Rubber XJ-Series


The workbench height of XJ-Series is very low and it was most interested in by customers' requirement.
The low workbench height makes it possible to improve the workability and safety of workers.
And also XJ is able to contribute to be space saving in factory because total height and width of XJ is lower and narrower.
As for energy saving, XJ is much improved by adopting an idle-speed control pump with inverter motor drive and a heat insulation board.
Matsuda boasts about XJ in the point of excellent features and functionalities as above.
XJ is an excellent cost-effective machine for you and Matsuda can provide XJ to all customers by reasonable price.

 
VI-200P(XJ)-40/70SPR2
Clamping Force KN (Ton) 1960 (200)
Injection Capacity cm3 1500
Total Height mm 4187
Total Width mm 1100
Total Depth mm 2862
Daylight mm 600
Stroke mm 400
Heating PlatenDiameter mm 600 x 600
Work Height mm 867
Feature 1 Low workbench height
The workbench height is 185 mm lower than with our previous model, eliminating the need to set up another workbench and thereby boosting safety and work efficiency.
Workbench height
@@Previous model:1,052mm -> XJ:867mm

Feature 2 Saves space
The dramatically reduced machine dimensions maximize productivity from limited factory floorspace.
Total Height
@@Previous model:4,567mm -> XJ:4,187mm
Total Width
@@Previous model:1,425mm -> XJ:1,100mm

Feature 3 Energy efficient
The rotation control pump featuring an inverter motor and the high effectivenessinsulation plate significantly reduce power consumption.
While actual power savings will vary with molding conditions, power consumption is typically approximately 30% lower than in our previous model (WJ).

Feature 4 Quiet operating sound
The rotation control pump features reduced pump motor driving noise to help improve the factory work environment.

Feature 5 Reduced molding cycle times
The smooth motion of the moving parts helps reduce molding cycle times.

Feature 6 Improved distribution of molding stress
We optimized the rigidity of each structural part based on analysis of contact pressures on mold mating surfaces by CAE, resulting in more uniform pressure distribution compared to previous models and helping to reduce burrs and enhance precision.